[질문]데비안 네떡/PCMCIA랜카드 설정:Device busy!
Siocsifflags: Device or resource busy 에러!!
등록 2005-02-04 14:08:15 조회 0
이름 왕초보
데비안 설치하려고 하는데 네트워크 설정 때문에 진전이 없네요.. 현재 3일째
삽질만 하고 있습니다.
=========================================================
제가 3.0r4로 노트북에 네트웍 설치를 하려고 합니다. 랜카드는 리얼텍 호환랜
카드(Zioncom-pcmcia : 윈도우에서 winipcfg를 해봐서 Realteck RTL8139라는
것을 알아냈습니다.)이구요.. 근데 설치 중에 dhcp와 bootp로 인터넷 설정을
가져오겠습니까 하는 부분에서 정보를 못가져 오더라구요. 여러번 시도해도 안
되서 그냥 다음단계로 넘어갔습니다.
아얄씨도 돌아다녀보고 KLDP라든지 이곳의 위키검색, 기존 홈피 검색까지 하면
서 알아봤는데 랜카드가 인식이 안되는 거라고 하더라구요.. 근데 부팅시 불
도 들어오고 소리도 "삑"합니다.
근데 dmesg를 해보면 8139too를 할때 위의 에러가 나면서 모듈이 적재되지 않
고, 그 이하 모든 랜카드 설정 및 eth0인터페이스가 에러가 나더라구요..
또, 항상 부팅하고 나면 lsmod했을때 8139too가 올라와 있지 않구요. 그래서
modconf로 모듈을 올려보는데, 그땐 잘 올라오긴합니다(근데 lsmod시 unused이
더군요) 여기서 부팅시 왜 "제목"의 에러가 나는지, 또 pcmcia카드를 어떻게
하면 제대로 인식시킬 수 있는지 알려주셨으면합니다.
또, 정보를 찾다가 보니 pnp설정을 해제시키면 된다고나와있는데요, 저희집 놋
북이 sens 820인데, 바이오스 셋팅시 pnp해제와 관련된 내용은 찾을 수가 없네
요.. 이에 대해 인터넷 뒤져보니까 도스용 바이오스 수정 유틸이 있다는데, 어
느것인지 찾을 수가 없더라구요.. 이런 유틸이 어디 있는지도 알려주셨으면 합
니다.
....
pnp 세팅은 커널컴파일을 새로 하셔야 할 겁니다.
No Pain, No Gain.
글 내용중에 8139too 모듈에 대해서만 언급하셔서 혹시 PCMCIA
글 내용중에 8139too 모듈에 대해서만 언급하셔서 혹시 PCMCIA 버스 지원 부분을 활성화 하지 않으신게 아닌가 하는 생각이 듭니다.
--
마잇
dmesg 올립니다..
우디 3.0r4에서 커널 2.4으로 설치했는데도 불구하고 리얼텍 카드를 인식할 수 없더군요.. dmesg를 올립니다.
Linux version 2.4.18-bf2.4 (root@zombie) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Son Apr 14 09:53:28 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ea800 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000004000000 (usable)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
On node 0 totalpages: 16384
zone(0): 4096 pages.
zone(1): 12288 pages.
zone(2): 0 pages.
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Kernel command line: BOOT_IMAGE=Linux ro root=305
Initializing CPU#0
Detected 501.143 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 999.42 BogoMIPS
Memory: 61168k/65536k available (1783k kernel code, 3980k reserved, 549k data, 280k init, 0k highmem)
Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd9ae, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DARA-212000, ATA DISK drive
hdc: SAMSUNG CD-ROM SN-124, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 23579136 sectors (12073 MB) w/418KiB Cache, CHS=24951/15/63
hdc: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.97.sv
Partition check:
hda: [PTBL] [1559/240/63] hda1 hda2 hda3 < hda5 hda6 > hda4
floppy0: no floppy controllers found
Loading I2O Core - (c) Copyright 1999 Red Hat Software
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
loop: loaded (max 8 devices)
Compaq CISS Driver (v 2.4.5)
HDLC support module revision 1.02 for Linux 2.4
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
ide-floppy driver 0.97.sv
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01
No raid array found
SCSI subsystem driver Revision: 1.00
Red Hat/Adaptec aacraid driver, Apr 14 2002
DC390: 0 adapters found
3ware Storage Controller device driver for Linux v1.02.00.016.
3w-xxxx: No cards with valid units found.
request_module[scsi_hostadapter]: Root fs not mounted
request_module[scsi_hostadapter]: Root fs not mounted
i2o_scsi.c: Version 0.0.1
chain_pool: 0 bytes @ c113ede0
(512 byte buffers X 4 can_queue X 0 i2o controllers)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 280k freed
Adding Swap: 309920k swap-space (priority -1)
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,5), internal journal
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 10:29:43 Apr 14 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Enabling device 00:07.2 (0000 -> 0001)
PCI: Found IRQ 5 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0x1020, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver keyboard
usbkbd.c: :USB HID Boot Protocol keyboard driver
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,4), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Linux PCMCIA Card Services 3.1.33
kernel build: 2.4.18-bf2.4 unknown
options: [pci] [cardbus] [apm]
Intel ISA/PCI/CardBus PCIC probe:
PCI: Found IRQ 11 for device 00:08.0
PCI: Sharing IRQ 11 with 00:08.1
PCI: Sharing IRQ 11 with 00:0d.0
PCI: Found IRQ 11 for device 00:08.1
PCI: Sharing IRQ 11 with 00:08.0
PCI: Sharing IRQ 11 with 00:0d.0
TI 1251B rev 00 PCI-to-CardBus at slot 00:08, mem 0x10000000
host opts [0]: [ring] [serial pci & irq] [pci irq 11] [lat 168/176] [bus 2/5]
host opts [1]: [ring] [serial pci & irq] [pci irq 11] [lat 168/176] [bus 6/9]
ISA irqs (scanned) = 3,4,7,10 PCI status changes
cs: cb_alloc(bus 2): vendor 0x10ec, device 0x8139
cs: cb_free(bus 2)
cs: cb_alloc(bus 2): vendor 0x10ec, device 0x8139
VFS: Disk change detected on device ide1(22,0)
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
usb-uhci.c: interrupt, status 28, frame# 1565
usb-uhci.c: Host controller halted, trying to restart.
cs: cb_free(bus 2)
cs: cb_alloc(bus 2): vendor 0x10ec, device 0x8139
cs: cb_free(bus 2)
unloading PCMCIA Card Services
Linux PCMCIA Card Services 3.1.33
kernel build: 2.4.18-bf2.4 unknown
options: [pci] [cardbus] [apm]
Intel ISA/PCI/CardBus PCIC probe:
PCI: Found IRQ 11 for device 00:08.0
PCI: Sharing IRQ 11 with 00:08.1
PCI: Sharing IRQ 11 with 00:0d.0
PCI: Found IRQ 11 for device 00:08.1
PCI: Sharing IRQ 11 with 00:08.0
PCI: Sharing IRQ 11 with 00:0d.0
TI 1251B rev 00 PCI-to-CardBus at slot 00:08, mem 0x10000000
host opts [0]: [ring] [serial pci & irq] [pci irq 11] [lat 168/176] [bus 2/5]
host opts [1]: [ring] [serial pci & irq] [pci irq 11] [lat 168/176] [bus 6/9]
ISA irqs (scanned) = 3,4,7,10 PCI status changes
cs: cb_alloc(bus 2): vendor 0x10ec, device 0x8139
// 여기 맨 마지막을 보면 분명 PCMCIA 카드를 인식했으며, 그 카드를 0x8139 - 리얼텍 랜카드라고 식별합니다. 그런데 ifconfig -a 시 eth0가 보이지 않는 것은 왜일까요.. 분명 커널 2.4인데도 리얼텍이 들어가 있지 않는건지...
^_^ 데뱐초보~
댓글 달기