CentOS 노트북 사운드 카드 셋팅이 되지 않습니다.

펜750에 램256 하드 10기가
시스템을 쓰고 있습니다.
노트북 CDROM이 고장나서 CentOS 설치 꽁수를 생각하다가
다른 시스템에 물려 CD부팅 후 네트워크 인스톨로 설치했습니다.
문제는 랜카드는 자동으로 잡는데 그래픽과 사운드 모듈이 제대로 올라가지 않는다더랬죠.
setup해서 x윈도우 설정 잡으니 비디오카드는 잘 잡더라구요.
헌데 사운드 모듈이 문제입니다.

lspci -v로 확인을 하니 ali5451, IRQ=10과 IO주소=1000이 할당이 되어 있군요.
[disabled]가 조금 걸리긴 하지만 모듈 올리기에 들어갔습니다.

/lib/modules/2.6.18-92.el5/kernel/sound/pci/ali5451/snd-ali5451.ko
파일이 있더군요.

/etc/modprobe.conf를 열고
alias snd-card-0 snd-ali5451
options snd-ali5451 irq=10 io=1000

이렇게 주고
modprobe snd-ali5451 하니 에러가!

Unknown symbol in module, or unknown parameter(see dmesg)
dmesg를 보니 irq파라미터를 알수 없다 하기에 modprobe.conf에서 irq를 지움.
그 후 io파라미터도 알수 없데서 io도 지움.

이제 에러가 나지 않더군요. 허나 모듈이 올라갔는데도
mp3blaster를 실행하니 카드를 찾을 수 없다는 에러를 뿜어대고
x윈도우에서도 인식을 못하는지 알림음도 못내는 겁니다.

이번에는 저 모듈이 올라가 있는상태에서
modprobe snd-ali5451 io=1000 irq=10 쳤습니다.
에러없이 진행이 잘 되던데 여전히 소리는 안나더군요.

dmesg에
PCI: Enableing device 0000:00:08.0 (0000-> 0003)
ACPI:PCI Interrupt 0000:00:08.0[A] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10
PCI : Unable to reserve I/O region #1:100@1000 for device 0000:00:08.0
ALI 5451:probe of 0000:00:08.0 failed with error -16
이 뜨는 걸로 봐서 정상작동은 안되는가 봅니다.

irq가 모자랄까봐 시리얼 포트를 CMOS에서 죽여놓았습니다.
dmesg를 보니 0x1000이란 주소가 예약되어 있다는 것 같기도 하고...
정확히 작동 안되는 원인을 모르겠습니다.
lspci에서 보니 ali5451이 사운드가 맞는 것 같고
irq와 io주소값 찾고 모듈에서 정확히 올려주면 되는 것 아닌지요?

어떻게하면 해결이 될수 있을지요.
lsmod |grep snd해서 보니
ali5451모듈은 다른 모듈에 의해 사용되고 있지 않다고 나오네요.
혹시 모듈이 올라갈 때 쓸데 없는 모듈이 같이 올라가서 충돌이 나는 것은 아닌지
lsmod부분을 조금 살펴봐 주셨으면 좋겠습니다.
모듈을 다 내리고 ali5451모듈만 올릴 때 같이 올라가는 모듈과 연관 있을 만한 부분을 굵게 표시하였습니다.

[root@apple2 /]# lspci -v
00:00.0 Host bridge: ALi Corporation M1621 (rev 01)
Flags: bus master, slow devsel, latency 0
Memory at f0000000 (32-bit, prefetchable) [=64M]
Capabilities: [b0] AGP version 1.0
Capabilities: [a4] Power Management version 1

00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: ee900000-efffffff
Prefetchable memory behind bridge: 14000000-140fffff

00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI])
Subsystem: Unknown device 168f:0001
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at ee800000 (32-bit, non-prefetchable) [=4K]
Capabilities: [60] Power Management version 2

00:03.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01)
Subsystem: Unknown device 168f:0001
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at 14100000 (32-bit, non-prefetchable) [=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10000000-11fff000 (prefetchable)
Memory window 1: 12000000-13fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
16-bit legacy interface ports at 0001

00:06.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
Subsystem: Unknown device 168f:0001
Flags: medium devsel

00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+]
Subsystem: Unknown device 168f:0001
Flags: bus master, medium devsel, latency 0
Capabilities: [a0] Power Management version 1

00:08.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 01)
Subsystem: Unknown device 168f:0001
Flags: medium devsel, IRQ 10
I/O ports at 1000 [disabled] [=256]
Memory at ee801000 (32-bit, non-prefetchable) [disabled] [=4K]
Capabilities: [dc] Power Management version 2

00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c3) (prog-if b0)
Subsystem: Unknown device 168f:0001
Flags: bus master, medium devsel, latency 32
I/O ports at
I/O ports at
I/O ports at
I/O ports at
I/O ports at 1400 [=16]
Capabilities: [60] Power Management version 2

01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (rev 5d) (prog-if 00 [VGA controller])
Subsystem: Unknown device 168f:0001
Flags: bus master, fast Back2Back, 66MHz, medium devsel, latency 64, IRQ 9
Memory at ef800000 (32-bit, non-prefetchable) [=8M]
Memory at ee900000 (32-bit, non-prefetchable) [=128K]
Memory at ef000000 (32-bit, non-prefetchable) [=8M]
[virtual] Expansion ROM at 14000000 [disabled] [=64K]
Capabilities: [80] AGP version 1.0
Capabilities: [90] Power Management version 1

02:00.0 Ethernet controller: ADMtek 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 11)
Subsystem: Accton Technology Corporation Unknown device 1216
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at 1800 [=256]
Memory at 12000000 (32-bit, non-prefetchable) [=1K]
[virtual] Expansion ROM at 10000000 [disabled] [=128K]
Capabilities: [c0] Power Management version 2

[root@apple2 /]#

[root@apple2 ali5451]# mount /dev/sda1 /sda
[root@apple2 ali5451]# mp3blaster
[root@apple2 ali5451]# modprobe snd-ali5451 io=1000 irq=10
[root@apple2 ali5451]# mp3blaster
[root@apple2 ali5451]#
[root@apple2 ali5451]# lsmod |grep snd
snd_ali5451 25549 0
snd_ac97_codec 93025 1 snd_ali5451
ac97_bus 6337 1 snd_ac97_codec
snd_seq_oss 32577 0
snd_seq_midi_event 11073 1 snd_seq_oss
snd_seq 49585 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 11725 2 snd_seq_oss,snd_seq
snd_pcm_oss 42945 0
snd_mixer_oss 19009 1 snd_pcm_oss
snd_pcm 72005 3 snd_ali5451,snd_ac97_codec,snd_pcm_oss
snd_timer 24517 2 snd_seq,snd_pcm
snd 52421 9 snd_ali5451,snd_ac97_codec,snd_seq_oss,snd_seqnd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 11553 1 snd
snd_page_alloc 14281 1 snd_pcm

[root@apple2 ali5451]# rmmod snd_ali5451
[root@apple2 ali5451]# rmmod snd_ac97_codec
[root@apple2 ali5451]# rmmod snd_seq_oss
[root@apple2 ali5451]# rmmod seq_midi_event
ERROR: Module seq_midi_event does not exist in /proc/modules
[root@apple2 ali5451]# lsmod |grep snd
snd_seq_midi_event 11073 0
snd_seq 49585 1 snd_seq_midi_event
snd_seq_device 11725 1 snd_seq
snd_pcm_oss 42945 0
snd_mixer_oss 19009 1 snd_pcm_oss
snd_pcm 72005 1 snd_pcm_oss
snd_timer 24517 2 snd_seq,snd_pcm
snd 52421 6 snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_o,snd_pcm,snd_timer
soundcore 11553 1 snd
snd_page_alloc 14281 1 snd_pcm
[root@apple2 ali5451]# rmmod snd_seq_midi_event
[root@apple2 ali5451]# rmmod snd_seq
[root@apple2 ali5451]# rmmod snd_pcm_oss
[root@apple2 ali5451]# rmmod snd_seq_device
[root@apple2 ali5451]# rmmod snd
ERROR: Module snd is in use by snd_mixer_oss,snd_pcm,snd_timer
[root@apple2 ali5451]# rmmod snd_pcm
[root@apple2 ali5451]# lsmod |grep snd
snd_mixer_oss 19009 0
snd_timer 24517 0
snd 52421 2 snd_mixer_oss,snd_timer
soundcore 11553 1 snd
snd_page_alloc 14281 0
[root@apple2 ali5451]# rmmod snd_mixer_oss
[root@apple2 ali5451]# rmmod snd_timer
[root@apple2 ali5451]# rmmod snd
[root@apple2 ali5451]# lsmod |grep snd
snd_page_alloc 14281 0
[root@apple2 ali5451]# rmmod snd_page_alloc
[root@apple2 ali5451]# cls
bash: cls: command not found
[root@apple2 ali5451]# clear

[root@apple2 ali5451]# modprobe snd-ali5451

[root@apple2 ali5451]# lsmod |grep snd
snd_ali5451 25549 0
snd_ac97_codec 93025 1 snd_ali5451
snd_seq_oss 32577 0
snd_seq_midi_event 11073 1 snd_seq_oss
snd_seq 49585 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 11725 2 snd_seq_oss,snd_seq
snd_pcm_oss 42945 0
snd_mixer_oss 19009 1 snd_pcm_oss
snd_pcm 72005 3 snd_ali5451,snd_ac97_codec,snd_pcm_oss
snd_timer 24517 2 snd_seq,snd_pcm
snd 52421 9 snd_ali5451,snd_ac97_codec,snd_seq_oss,snd_seqnd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
snd_page_alloc 14281 1 snd_pcm
ac97_bus 6337 1 snd_ac97_codec
soundcore 11553 1 snd

[root@apple2 ali5451]# mp3blaster
[root@apple2 ali5451]# dmesg
Linux version 2.6.18-92.el5 (mockbuild@builder16.centos.org) (gcc version 4.1.20071124 (Red Hat 4.1.2-42)) #1 SMP Tue Jun 10 18:49:47 EDT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ec800 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f7f0000 (usable)
BIOS-e820: 000000000f7f0000 - 000000000f7ffc00 (ACPI data)
BIOS-e820: 000000000f7ffc00 - 000000000f800000 (ACPI NVS)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
247MB LOWMEM available.
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 63472
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 59376 pages, LIFO batch:15
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 KDST ) @ 0x000f7600
ACPI: RSDT (v001 KDST SUMO 0x00000001 PTL 0x00000000) @ 0x0f7fceb7
ACPI: FADT (v001 KDST SUMO 0x00000001 PTL 0x000f4240) @ 0x0f7ffb8c
ACPI: DSDT (v001 KDST SUMO 0x00000001 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
Allocating PCI resources starting at 10000000 (gap: 0f800000:f07c0000)
Detected 747.277 MHz processor.
Built 1 zonelists. Total pages: 63472
Kernel command line: ro root=LABEL=/ rhgb quiet
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (011f9000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c074b000 soft=c072b000
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 244848k/253888k available (2095k kernel code, 8480k reserved, 874k dat 228k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1495.28 BogoMIPS (lpj=747644)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 000000000000000 00000000
CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 000000000000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383f1ff 00000000 00000000 00000040 00000000 000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0e00)
CPU0: Intel Pentium III (Coppermine) stepping 06
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=136 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
checking if image is initramfs... it is
Freeing initrd memory: 2203k freed
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8ce, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI Error (evregion-0317): No handler for Region [ERAM] (cf58d2cc) [EmbeddedCtrol] [20060707]
ACPI Error (exfldio-0290): Region EmbeddedControl(3) has no handler [20060707]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.ACAD._STA] (No cf586720), AE_NOT_EXIST
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 8000-803f claimed by ali7101 ACPI
PCI quirk: region 8040-805f claimed by ali7101 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 7 9 10 *11 12)
ACPI: Embedded Controller [EC0] (gpe 6) interrupt mode.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:07: ioport range 0x3810-0x381f has been reserved
pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:07: ioport range 0x8000-0x805f could not be reserved
pnp: 00:07: ioport range 0x1000-0x10ef has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: ee900000-efffffff
PREFETCH window: 14000000-140fffff
PCI: Bus 2, cardbus bridge: 0000:00:03.0
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> I 11
PCI: Setting latency timer of device 0000:00:03.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1234821791.170:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key D1F27370ACBC602E
- User ID: CentOS (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected ALi M1632 chipset
agpgart: AGP aperture is 64M @ 0xf0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:0f.0
ACPI: Unable to derive IRQ for device 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[A]: no GSI
ALI15X3: chipset revision 195
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1400-0x1407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1408-0x140f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK1016GAP, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: QSI CD-ROM SCR-242A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 19640880 sectors (10056 MB), CHS=19485/16/63, UDMA(33)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
ide-floppy driver 0.99.newide
Yenta: CardBus bridge found at 0000:00:03.0 [168f:0001]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:03.0, mfunc 0x01221c72, devctl 0x66
Yenta: ISA IRQ mask 0x04f8, PCI irq 11
Socket status: 30000020
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Time: tsc clocksource has been installed.
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 228k freed
Write protecting the kernel read-only data: 393k
Time: acpi_pm clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKU] -> GSI 11 (level, low) -> I 11
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 11, io mem 0xee800000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Synaptics Touchpad, model: 1, fw: 4.1, id: 0x848a1, caps: 0x0/0x0
pccard: CardBus card inserted into slot 0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1234821797.653:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=42949295
security: 3 users, 6 roles, 1676 types, 213 bools, 1 sens, 1024 cats
security: 61 classes, 60092 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hda6, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1234821799.185:3): policy loaded auid=4294967295 ses=4294967295
input: PC Speaker as /class/input/input2
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Linux Tulip driver version 1.1.13 (May 11, 2002)
PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> I 11
PCI: Setting latency timer of device 0000:02:00.0 to 64
tulip0: MII transceiver #1 config 3100 status 7869 advertising 05e1.
eth0: ADMtek Comet rev 17 at d003a000, 00:0A:CD:0A:75:8A, IRQ 11.
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKH] -> GSI 10 (level, low) -> I 10
PCI: Unable to reserve I/O region #1:100@1000 for device 0000:00:08.0
ACPI: PCI interrupt for device 0000:00:08.0 disabled
ALI 5451: probe of 0000:00:08.0 failed with error -16
FDC 0 is a post-1991 82077
lp: driver loaded but no devices found
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: IBM ThinkPad ACPI Extras v0.13-rh
ibm_acpi: http://ibm-acpi.sf.net/
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: dm-devel@redhat.c
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on hda6, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda5, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda3, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda2, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 926312k swap on /dev/hda7. Priority:-1 extents:1 across:926312k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a
microcode: CPU0 updated from revision 0x0 to 0x8, date = 05052000
floppy0: unexpected interrupt
floppy0: sensei repl[0]=23 repl[1]=80
floppy0: sensei repl[0]=80
SELinux: initialized (dev infinibandeventfs, type infinibandeventfs), not confured for labeling
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 27
SCSI subsystem initialized
Loading iSCSI transport class v2.0-724.
iscsi: registered transport (iser)
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (1983 buckets, 15864 max) - 228 bytes per conntrack
0000:02:00.0: tulip_stop_rxtx() failed
eth0: Setting full-duplex based on MII#1 link partner capability of 45e1.
eth0: no IPv6 routers present
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
snd_ali5451: Unknown parameter `irq'
snd_ali5451: Unknown parameter `irq'
snd_ali5451: Unknown parameter `io'
snd_ali5451: Unknown parameter `io'
PCI: Enabling device 0000:00:08.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKH] -> GSI 10 (level, low) -> I 10
PCI: Unable to reserve I/O region #1:100@1000 for device 0000:00:08.0
ACPI: PCI interrupt for device 0000:00:08.0 disabled
ALI 5451: probe of 0000:00:08.0 failed with error -16
floppy0: unexpected interrupt
floppy0: sensei repl[0]=c2 repl[1]=0
floppy0: sensei repl[0]=80
ohci_hcd 0000:00:02.0: wakeup
usb 1-1: new full speed USB device using ohci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: SanDisk Model: Cruzer Mini Rev: 0.1
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
scsi 0:0:0:0: Attached scsi generic sg0 type 0
SCSI device sda: 1000944 512-byte hdwr sectors (512 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 1000944 512-byte hdwr sectors (512 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
SELinux: initialized (dev sda1, type vfat), uses genfs_contexts
BUG: warning at fs/proc/generic.c:732/remove_proc_entry() (Not tainted)
[] remove_proc_entry+0x139/0x18c
[] snd_info_done+0x46/0x49 [snd]
[] alsa_sound_exit+0xa/0x30 [snd]
[] sys_delete_module+0x192/0x1b8
[] audit_syscall_entry+0x14b/0x17d
[] syscall_call+0x7/0xb
=======================
PCI: Enabling device 0000:00:08.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKH] -> GSI 10 (level, low) -> I 10
PCI: Unable to reserve I/O region #1:100@1000 for device 0000:00:08.0
ACPI: PCI interrupt for device 0000:00:08.0 disabled
ALI 5451: probe of 0000:00:08.0 failed with error -16

아 io=0x1000 으로 줘도 안됩니다 ㅠㅠ