dhcp 스크립트에서 호스트 이름을 불러 오지 않게 하려면..

다음은 /etc/sysconfig/network-scripts/ifup 의 스크립트입니다.

이 스크립트에 어디를 고쳐 줘야
DHCP 서버로 부터 자동으로 할당되는 호스트이름을 불러 오지 않을까요?

제가 스크립트는 아직 못 해운지라..

스트립트 올립니다.. 살펴 주십시오..

-----------------------------

[root@8804316 ~]# cat /etc/sysconfig/network-scripts/ifup
#!/bin/bash
# Network Interface Configuration System
# Copyright (c) 1996-2001 Red Hat, Inc. all rights reserved.
#
# This software may be freely redistributed under the terms of the GNU
# public license.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.

. /etc/init.d/functions

cd /etc/sysconfig/network-scripts
. network-functions

[ -f ../network ] && . ../network

CONFIG=${1}

[ -z "${CONFIG}" ] && {
echo $"Usage: ifup <device name>" >&2
exit 1
}

need_config ${CONFIG}

[ -f "${CONFIG}" ] || {
echo $"$0: configuration for ${1} not found." >&2
echo $"Usage: ifup <device name>" >&2
exit 1
}

if [ ${UID} != 0 ]; then
if [ -x /usr/sbin/usernetctl ]; then
source_config
if /usr/sbin/usernetctl ${CONFIG} report ; then
exec /usr/sbin/usernetctl ${CONFIG} up
fi
fi
echo $"Users cannot control this device." >&2
exit 1
fi

source_config

if [ "foo$2" = "fooboot" ] && [ "${ONBOOT}" = "no" -o "${ONBOOT}" = "NO" ]
then
exit 0
fi
if [ -n "$IN_HOTPLUG" ] && [ "${HOTPLUG}" = "no" -o "${HOTPLUG}" = "NO" ]
then
exit 0
fi
if [ -n "$IN_HOTPLUG" -a "${TYPE}" = "Bridge" ];
then
exit 0
fi

# Ethernet 802.1Q VLAN support
if [ -x /sbin/vconfig -a "${VLAN}" = "yes" ]; then
VID=""
if echo ${DEVICE} | LANG=C egrep -v '(:)' | LANG=C egrep -q '(eth|bond)[0-9][0-9]*\.[0-9][0-9]?[0-9]?[0-9]?'; then
VID="`echo ${DEVICE} | \
LANG=C egrep '(eth|bond)[0-9]+\.[0-9][0-9]?[0-9]?[0-9]?$' | \
LANG=C sed 's/^[a-z0-9]*\.//g;s/^0*//'`"
PHYSDEV="`echo ${DEVICE} | \
LANG=C egrep '(eth|bond)[0-9]+\.[0-9][0-9]?[0-9]?[0-9]?$' | \
LANG=C sed 's/\.[a-z0-9]*$//g'`"
fi
if echo ${DEVICE} | LANG=C egrep -q 'vlan[0-9][0-9]?[0-9]?[0-9]?'; then
VID="`echo ${DEVICE} | LANG=C sed 's/^vlan//;s/^0*//'`"
# PHYSDEV should be set in ifcfg-vlan* file
if test -z "$PHYSDEV"; then
echo $"PHYSDEV should be set for device ${DEVICE}"
exit 1
fi
fi
if [ -n "$VID" ]; then
if [ ! -d /proc/net/vlan ]; then
if modprobe 8021q >/dev/null 2>&1 ; then
test -z "$VLAN_NAME_TYPE" && VLAN_NAME_TYPE=DEV_PLUS_VID_NO_PAD
/sbin/vconfig set_name_type "$VLAN_NAME_TYPE" >/dev/null 2>&1 || {
echo $"Could not set 802.1Q VLAN parameters."
}
else
echo $"No 802.1Q VLAN support available in kernel for device ${DEVICE}"
exit 1
fi
fi

is_available ${PHYSDEV} || {
if [ "$?" = "1" ] ; then
echo $"$alias device ${DEVICE} does not seem to be present, delaying initialization."
exit 1
else
exit 0
fi
}

# Link on Physical device needs to be up but no ip required
check_device_down ${PHYSDEV} && {
ip -o link set dev ${PHYSDEV} up
}

if [ ! -f /proc/net/vlan/${DEVICE} ]; then
/sbin/vconfig add ${PHYSDEV} ${VID} || {
(logger -p daemon.info -t ifup \
$"ERROR: could not add vlan ${VID} as ${DEVICE} on dev ${PHYSDEV}" &)&
echo $"ERROR: could not add vlan ${VID} as ${DEVICE} on dev ${PHYSDEV}"
exit 1
}
fi

if [ -f /proc/net/vlan/${DEVICE} ]; then
case "$REORDER_HDR" in
yes|1)
/sbin/vconfig set_flag ${DEVICE} 1 1 || {
(logger -p daemon.info -t ifup \
"WARNING: vconfig not able to enable REORDER_HDR on ${DEVICE}" &)&
}
;;
no|0)
/sbin/vconfig set_flag ${DEVICE} 1 0 || {
(logger -p daemon.info -t ifup \
$"WARNING: vconfig not able to disable REORDER_HDR on ${DEVICE}" &)&
}
;;
esac
fi
fi
fi

# Old BOOTP variable
if [ "${BOOTP}" = "yes" ]; then
BOOTPROTO=bootp
fi

if [ "${BOOTPROTO}" = "bootp" -o "${BOOTPROTO}" = "dhcp" ]; then
DYNCONFIG=true
fi

if [ -x /sbin/ifup-pre-local ]; then
/sbin/ifup-pre-local ${CONFIG} $2
fi

OTHERSCRIPT="/etc/sysconfig/network-scripts/ifup-${DEVICETYPE}"

if [ ! -x ${OTHERSCRIPT} ]; then
OTHERSCRIPT="/etc/sysconfig/network-scripts/ifup-eth"
fi

exec ${OTHERSCRIPT} ${CONFIG} $2

[root@8804316 ~]#