페도라5 에서 TF_6100(n-force4) 내장 랜카드가 정상적으로 작동되시는분?
이틀동안 랜카드때문에 고생했는데 도저히 정상적으로 작동하지 않네요
이상하게 모듈은 제대로 올라오고 ifconfig설정도 제대로 되는데 패킷을 송신을 모하는것 같은데...음
안될려면 아애 안되지 이놈때문에 흑흑...
일단 모듈 부분 입니다.
------------------------------------------------------
ne2k_pci 10657 0
snd_seq 47153 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 8909 3 snd_seq_dummy,snd_seq_oss,snd_seq
8390 9925 1 ne2k_pci
snd_pcm_oss 45009 0
snd_mixer_oss 16449 2 snd_pcm_oss
snd_pcm 76869 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 22597 2 snd_seq,snd_pcm
snd 50501 9 snd_intel8x0,snd_ac97_codec,snd_seq_oss,snd_seq, snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 9377 2 snd
forcedeth 22213 0 (이놈인데 왜 0으로 나오는진 모르겠네요)
------------------------------------------------------
dmesg 부분중에 모듈이 올라갈때 메세지는
------------------------------------------------------
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.49.
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:14.0 to 64
eth1: forcedeth.c: subsystem: 01565:2501 bound to 0000:00:14.0
eth1: no link during initialization.
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth1: link up.
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
eth1: no IPv6 routers present
------------------------------------------------------
잘은 모르겠지만 link is not ready 부분이 마음에 걸리네요...
마지막으로 ifconfig 부분은
------------------------------------------------------
eth0 Link encap:Ethernet HWaddr 00:50:BF:49:26:9B
inet addr:202.31.201.187 Bcast:202.31.201.255 Mask:255.255.255.0
inet6 addr: 2002:ca1f:c806:4:250:bfff:fe49:269b/64 Scope:Global
inet6 addr: fec0::4:250:bfff:fe49:269b/64 Scope:Site
inet6 addr: fe80::250:bfff:fe49:269b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:51530 errors:0 dropped:0 overruns:0 frame:0
TX packets:2791 errors:0 dropped:0 overruns:0 carrier:0
collisions:378 txqueuelen:1000
RX bytes:5959234 (5.6 MiB) TX bytes:481493 (470.2 KiB)
Interrupt:19 Base address:0xcc00
eth1 Link encap:Ethernet HWaddr 00:E0:4C:EE:E3:C5
inet addr:192.168.0.2 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:4cff:feee:e3c5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:44 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:17 Base address:0x2000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2329 errors:0 dropped:0 overruns:0 frame:0
TX packets:2329 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3153188 (3.0 MiB) TX bytes:3153188 (3.0 MiB)
------------------------------------------------------
eth1이 메인보드 랜카드인데 tx는 윈도우하고 연결해서 핑때려보면 rx부분이 잘올라가는데 tx는 모조리 drop 됩니다.
아마도 tx부분이 이상한것 같은데 여튼 정상적으로 작동되진 않네요;;
혹시 TF-6100메인보드 사용자중에서 랜카드 잘 사용하신분 있으시면 좀 알려주시면 감사하겠어요~~