Uncompressing Linux........................................................................................................................... done, booting the kernel. <5>Linux version 2.6.21.7-hrt1-moko11 (----@-------) (gcc version 4.1.2 (Wind River Linux Sourcery G++ 4.1-84)) #1 PREEMPT Mon Oct 26 18:34:15 KST 2009 CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177 Machine: GTA01 Memory policy: ECC disabled, Data cache writeback <7>On node 0 totalpages: 32768 <7> DMA zone: 256 pages used for memmap <7> DMA zone: 0 pages reserved <7> DMA zone: 32512 pages, LIFO batch:7 <7> Normal zone: 0 pages used for memmap CPU S3C2410A (id 0x32410002) S3C2410: core 266.000 MHz, memory 133.000 MHz, peripheral 66.500 MHz <6>S3C24XX Clocks, (c) 2004 Simtec Electronics CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets Built 1 zonelists. Total pages: 32512 <5>Kernel command line: root=/dev/nfs nfsroot=192.168.18.1:/export/dist,udp rw ip=192.168.200.15:192.168.200.1:192.168.200.1:255.255.255.0:qemu:eth0:off console=ttySAC0,115200 screen=320,240 mtdparts=neo1973-nand:0x00050000(u-boot) irq: clearing subpending status 00000002 PID hash table entries: 512 (order: 9, 2048 bytes) timer tcon=00500000, tcnt d877, tcfg 00000200,00000000, usec 00001719 Console: colour dummy device 80x30 Linux version 2.6.21.7-hrt1-moko11 (----@--------) (gcc version 4.1.2 (Wind River Linux Sourcery G++ 4.1-84)) #1 PREEMPT Mon Oct 26 18:34:15 KST 2009 CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177 Machine: GTA01 Memory policy: ECC disabled, Data cache writeback CPU S3C2410A (id 0x32410002) S3C2410: core 266.000 MHz, memory 133.000 MHz, peripheral 66.500 MHz S3C24XX Clocks, (c) 2004 Simtec Electronics CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets Built 1 zonelists. Total pages: 32512 Kernel command line: root=/dev/nfs nfsroot=192.168.18.1:/export/dist,udp rw ip=192.168.200.15:192.168.200.1:192.168.200.1:255.255.255.0:qemu:eth0:off console=ttySAC0,115200 screen=320,240 mtdparts=neo1973-nand:0x00050000(u-boot) irq: clearing subpending status 00000002 PID hash table entries: 512 (order: 9, 2048 bytes) timer tcon=00500000, tcnt d877, tcfg 00000200,00000000, usec 00001719 Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) <6>Memory:Memory: 128MB 128MB = 128MB total = 128MB total <5>Memory: 125824KB available (3472K code, 317K data, 200K init) Memory: 125824KB available (3472K code, 317K data, 200K init) <7>Calibrating delay loop... 660.27 BogoMIPS (lpj=1650688) <6>Security Framework v1.0.0 initialized Security Framework v1.0.0 initialized <6>Capability LSM initialized Capability LSM initialized Mount-cache hash table entries: 512 Mount-cache hash table entries: 512 <6>CPU: Testing write buffer coherency: CPU: Testing write buffer coherency: ok ok <6>NET: Registered protocol family 16 NET: Registered protocol family 16 S3C2410 Power Management, (c) 2004 Simtec Electronics S3C2410 Power Management, (c) 2004 Simtec Electronics <6>wake enabled for irq 17 wake enabled for irq 17 S3C2410: Initialising architecture S3C2410: Initialising architecture S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics DMA channel 0 at c8800000, irq 33 DMA channel 0 at c8800000, irq 33 DMA channel 1 at c8800040, irq 34 DMA channel 1 at c8800040, irq 34 DMA channel 2 at c8800080, irq 35 DMA channel 2 at c8800080, irq 35 DMA channel 3 at c88000c0, irq 36 DMA channel 3 at c88000c0, irq 36 <5>SCSI subsystem initialized SCSI subsystem initialized <6>usbcore: registered new interface driver usbfs usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb usbcore: registered new device driver usb <6>NET: Registered protocol family 2 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) <6>TCP: Hash tables configured (established 4096 bind 4096) TCP: Hash tables configured (established 4096 bind 4096) <6>TCP reno registered TCP reno registered <4>NetWinder Floating Point Emulator V0.97 (double precision) NetWinder Floating Point Emulator V0.97 (double precision) Registering GDB sysrq handler Registering GDB sysrq handler <6>JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc. JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc. yaffs Oct 26 2009 18:30:24 Installing. yaffs Oct 26 2009 18:30:24 Installing. <6>Registering unionfs 2.1.6 (for 2.6.21.7) Registering unionfs 2.1.6 (for 2.6.21.7) <6>io scheduler noop registered io scheduler noop registered <6>io scheduler deadline registered (default) io scheduler deadline registered (default) <6>LTT : ltt-facilities init LTT : ltt-facilities init <6>LTT : ltt-relay init LTT : ltt-relay init GTA01 Backlight Driver Initialized. GTA01 Backlight Driver Initialized. <7>s3c2410fb: devinit <7>s3c2410fb: got LCD region <7>s3c2410fb: got and enabled clock <7>s3c2410fb: map_video_memory(fbi=c0577220) <7>s3c2410fb: map_video_memory: clear ffc00000:0012c000 <7>s3c2410fb: map_video_memory: dma=37c00000 cpu=ffc00000 size=0012c000 <7>s3c2410fb: got video memory <7>s3c2410fb: LCDSADDR1 = 0x1be00000 <7>s3c2410fb: LCDSADDR2 = 0x1be12c00 <7>s3c2410fb: LCDSADDR3 = 0x000000f0 <7>s3c2410fb: LPCSEL = 0x00000cf0 <7>s3c2410fb: replacing TPAL 00000000 <7>s3c2410fb: check_var(var=c0577008, info=c0577000) <7>s3c2410fb: s3c2410fb_activate_var: var->xres = 240 <7>s3c2410fb: s3c2410fb_activate_var: var->yres = 320 <7>s3c2410fb: s3c2410fb_activate_var: var->bpp = 16 <7>s3c2410fb: setting vert: up=2, low=16, sync=2 <7>s3c2410fb: setting horz: lft=104, rt=8, sync=8 <7>s3c2410fb: new register set: <7>s3c2410fb: lcdcon[1] = 0x00000179 <7>s3c2410fb: lcdcon[2] = 0x014fc3c1 <7>s3c2410fb: lcdcon[3] = 0x0038ef67 <7>s3c2410fb: lcdcon[4] = 0x00000007 <7>s3c2410fb: lcdcon[5] = 0x00000f09 <7>s3c2410fb: LCDSADDR1 = 0x1be00000 <7>s3c2410fb: LCDSADDR2 = 0x1be12c00 <7>s3c2410fb: LCDSADDR3 = 0x000000f0 Console: switching to colour frame buffer device 30x40 Console: switching to colour frame buffer device 30x40 <6>fb0: s3c2410fb frame buffer device fb0: s3c2410fb frame buffer device <6>s3c2410-uart.0: s3c2410_serial0 at MMIO map 0x50000000 mem 0xf0400000 (irq = 70) is a S3C2410 s3c2410-uart.0: s3c2410_serial0 at MMIO map 0x50000000 mem 0xf0400000 (irq = 70) is a S3C2410 <6>s3c2410-uart.1: s3c2410_serial1 at MMIO map 0x50004000 mem 0xf0404000 (irq = 73) is a S3C2410 s3c2410-uart.1: s3c2410_serial1 at MMIO map 0x50004000 mem 0xf0404000 (irq = 73) is a S3C2410 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize <6>loop: loaded (max 8 devices) loop: loaded (max 8 devices) smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre eth0: SMC91C11xFD (rev 1) at c885e000 IRQ 18eth0: SMC91C11xFD (rev 1) at c885e000 IRQ 18 [nowait] [nowait] eth0: Ethernet addr: eth0: Ethernet addr: 52:52:54:54:00:00:12:12:34:34:56 56 <7>eth0: No PHY found <6>Linux video capture interface: v2.00 Linux video capture interface: v2.00 <4>videodev: "vivi" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/ videodev: "vivi" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/ <6>Video Technology Magazine Virtual Video Capture Board (Load status: 0) Video Technology Magazine Virtual Video Capture Board (Load status: 0) <6>i2c /dev entries driver i2c /dev entries driver <6>s3c2410-i2c s3c2410-i2c: slave address 0x10 s3c2410-i2c s3c2410-i2c: slave address 0x10 <6>s3c2410-i2c s3c2410-i2c: bus frequency set to 377 KHz s3c2410-i2c s3c2410-i2c: bus frequency set to 377 KHz <6>s3c2410-i2c s3c2410-i2c: i2c-0: S3C I2C adapter s3c2410-i2c s3c2410-i2c: i2c-0: S3C I2C adapter <6>input: FIC Neo1973 PMU events as /class/input/input0 input: FIC Neo1973 PMU events as /class/input/input0 <6>wake enabled for irq 53 wake enabled for irq 53 <7>pcf50606 0-0008: rtc intf: sysfs <7>pcf50606 0-0008: rtc intf: proc <7>pcf50606 0-0008: rtc intf: dev (254:0) <6>pcf50606 0-0008: rtc core: registered pcf50606 as rtc0 pcf50606 0-0008: rtc core: registered pcf50606 as rtc0 <6>gta01-pm-bt gta01-pm-bt.0: FIC GTA01 (Neo1973) Bluetooth Power Management: starting gta01-pm-bt gta01-pm-bt.0: FIC GTA01 (Neo1973) Bluetooth Power Management: starting pcf50633_attach_adapter: entering, calling i2c_probe pcf50633_attach_adapter: entering, calling i2c_probe S3C24XX NAND Driver, (c) 2004 Simtec Electronics S3C24XX NAND Driver, (c) 2004 Simtec Electronics <6>s3c2410-nand s3c2410-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns s3c2410-nand s3c2410-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns <6>NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit) NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit) s3c2410_nand_update_chip: chip c0647ebc: 9 s3c2410_nand_update_chip: chip c0647ebc: 9 <7>Bad block table found at page 262112, version 0x01 <7>Bad block table found at page 262080, version 0x01 <5>1 cmdlinepart partitions found on MTD device neo1973-nand 1 cmdlinepart partitions found on MTD device neo1973-nand <5>Creating 1 MTD partitions on "neo1973-nand": Creating 1 MTD partitions on "neo1973-nand": <5>0x00000000-0x00050000 : "u-boot" 0x00000000-0x00050000 : "u-boot" <6>s3c2410-nand s3c2410-nand: clock idle support enabled s3c2410-nand s3c2410-nand: clock idle support enabled <6>s3c24xx-spi-gpio s3c24xx-spi-gpio.1: registering c0023fb4: jbt6k74 s3c24xx-spi-gpio s3c24xx-spi-gpio.1: registering c0023fb4: jbt6k74 <3>jbt_init: entering jbt_init: entering <3>jbt_probe: entering jbt_probe: entering <3>jbt6k74_enter_state: entering(old_state=0, new_state=2) jbt6k74_enter_state: entering(old_state=0, new_state=2) <3>standby_to_sleep: entering standby_to_sleep: entering <3>sleep_to_normal: entering sleep_to_normal: entering <3>jbt_init_regs: entering jbt_init_regs: entering <3>jbt6k74_display_onoff: entering jbt6k74_display_onoff: entering <7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver <6>s3c2410-ohci s3c2410-ohci: S3C24XX OHCI s3c2410-ohci s3c2410-ohci: S3C24XX OHCI <6>s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1 s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1 <6>s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000 s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000 <6>usb usb1: configuration #1 chosen from 1 choice usb usb1: configuration #1 chosen from 1 choice <6>hub 1-0:1.0: USB hub found hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 3 ports detected hub 1-0:1.0: 3 ports detected <6>usb 1-2: new full speed USB device using s3c2410-ohci and address 2 usb 1-2: new full speed USB device using s3c2410-ohci and address 2 <6>usb 1-2: configuration #1 chosen from 1 choice usb 1-2: configuration #1 chosen from 1 choice <6>usb 1-3: new full speed USB device using s3c2410-ohci and address 3 usb 1-3: new full speed USB device using s3c2410-ohci and address 3 <6>usb 1-3: configuration #1 chosen from 1 choice usb 1-3: configuration #1 chosen from 1 choice <6>usbcore: registered new interface driver libusual usbcore: registered new interface driver libusual <6>input: QEMU 0.9.0 QEMU USB Keyboard as /class/input/input1 input: QEMU 0.9.0 QEMU USB Keyboard as /class/input/input1 <6>inputinput: USB HID v1.11 Keyboard [QEMU 0.9.0 QEMU USB Keyboard] on usb-s3c24xx-2 : USB HID v1.11 Keyboard [QEMU 0.9.0 QEMU USB Keyboard] on usb-s3c24xx-2 <6>usbcore: registered new interface driver usbhid usbcore: registered new interface driver usbhid <6>drivers/usb/input/hid-core.c: v2.6:USB HID core driver drivers/usb/input/hid-core.c: v2.6:USB HID core driver <7>gta01_udc_command(2) <4>ether gadget: using random self ethernet address ether gadget: using random self ethernet address <4>ether gadget: using random host ethernet address ether gadget: using random host ethernet address <6>usb0: Ethernet Gadget, version: May Day 2005 usb0: Ethernet Gadget, version: May Day 2005 <6>usb0: using s3c2410_udc, OUT ep2-bulk IN ep1-bulk STATUS ep3-bulk usb0: using s3c2410_udc, OUT ep2-bulk IN ep1-bulk STATUS ep3-bulk <6>usb0: MAC 0a:d7:a2:85:9c:d9 usb0: MAC 0a:d7:a2:85:9c:d9 <6>usb0: HOST MAC 72:56:62:96:63:fe usb0: HOST MAC 72:56:62:96:63:fe <6>usb0: RNDIS ready usb0: RNDIS ready <7>gta01_udc_command(1) <6>mice: PS/2 mouse device common for all mice mice: PS/2 mouse device common for all mice <6>s3c2410 TouchScreen successfully loaded s3c2410 TouchScreen successfully loaded <6>input: s3c2410 TouchScreen as /class/input/input2 input: s3c2410 TouchScreen as /class/input/input2 mapped channel 0 to 0 mapped channel 0 to 0 <7>mmc_set_power(power_mode=0, vdd=0 <6>s3c2410-sdi s3c2410-sdi: powered down. s3c2410-sdi s3c2410-sdi: powered down. <6>s3c2410-sdi s3c2410-sdi: initialisation done. s3c2410-sdi s3c2410-sdi: initialisation done. <7>mmc_set_power(power_mode=1, vdd=20 <6>s3c2410-sdi s3c2410-sdi: running at 0kHz (requested: 0kHz). s3c2410-sdi s3c2410-sdi: running at 0kHz (requested: 0kHz). <7>mmc_set_power(power_mode=2, vdd=20 <6>s3c2410-sdi s3c2410-sdi: running at 130kHz (requested: 129kHz). s3c2410-sdi s3c2410-sdi: running at 130kHz (requested: 129kHz). <7>mmc_set_power(power_mode=2, vdd=20 <6>s3c2410-sdi s3c2410-sdi: running at 130kHz (requested: 129kHz). s3c2410-sdi s3c2410-sdi: running at 130kHz (requested: 129kHz). <7>mmc_set_power(power_mode=2, vdd=20 <6>s3c2410-sdi s3c2410-sdi: running at 130kHz (requested: 129kHz). s3c2410-sdi s3c2410-sdi: running at 130kHz (requested: 129kHz). <6>Registered led device: gta01:vibrator Registered led device: gta01:vibrator <6>Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC). Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC). <6>ASoC version 0.13.0 ASoC version 0.13.0 <6>wm8753: WM8753 Audio Codec 0.16 wm8753: WM8753 Audio Codec 0.16 <7>mmc_set_power(power_mode=0, vdd=0 <6>s3c2410-sdi s3c2410-sdi: powered down. s3c2410-sdi s3c2410-sdi: powered down. <6>asoc: WM8753 HiFi <-> s3c24xx-i2s mapping ok asoc: WM8753 HiFi <-> s3c24xx-i2s mapping ok <6>asoc: WM8753 Voice <-> Bluetooth mapping ok asoc: WM8753 Voice <-> Bluetooth mapping ok <6>ALSA device list: ALSA device list: <6> #0: neo1973 (WM8753) #0: neo1973 (WM8753) <6>TCP cubic registered TCP cubic registered <6>NET: Registered protocol family 1 NET: Registered protocol family 1 <5>Bridge firewalling registered Bridge firewalling registered <6>pcf50606 0-0008: setting the system clock to 2009-11-07 11:06:51 (1257592011) pcf50606 0-0008: setting the system clock to 2009-11-07 11:06:51 (1257592011) <6>eth0: link up eth0: link up IP-Config: Complete:IP-Config: Complete: device=eth0 device=eth0, addr=192.168.200.15, addr=192.168.200.15, mask=255.255.255.0, mask=255.255.255.0, gw=192.168.200.1, gw=192.168.200.1, host=qemu, domain=, nis-domain=(none), host=qemu, domain=, nis-domain=(none), bootserver=192.168.200.1, bootserver=192.168.200.1, rootserver=192.168.18.1, rootserver=192.168.18.1, rootpath=, rootpath= <5>Looking up port of RPC 100003/2 on 192.168.18.1 Looking up port of RPC 100003/2 on 192.168.18.1 <5>portmap: server 192.168.18.1 not responding, timed out portmap: server 192.168.18.1 not responding, timed out <3>Root-NFS: Unable to get nfsd port number from server, using default Root-NFS: Unable to get nfsd port number from server, using default <5>Looking up port of RPC 100005/1 on 192.168.18.1 Looking up port of RPC 100005/1 on 192.168.18.1 <5>portmap: server 192.168.18.1 not responding, timed out portmap: server 192.168.18.1 not responding, timed out <3>Root-NFS: Unable to get mountd port number from server, using default Root-NFS: Unable to get mountd port number from server, using default <5>mount: server 192.168.18.1 not responding, timed out mount: server 192.168.18.1 not responding, timed out <3>Root-NFS: Server returned error -5 while mounting /export/dist Root-NFS: Server returned error -5 while mounting /export/dist <3>VFS: Unable to mount root fs via NFS, trying floppy. VFS: Unable to mount root fs via NFS, trying floppy. VFS: Cannot open root device "nfs" or unknown-block(2,0) VFS: Cannot open root device "nfs" or unknown-block(2,0) Please append a correct "root=" boot option Please append a correct "root=" boot option <0>Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)